FROM $379.99
4200Pa Suction
3D Mapping
5200mAh Battery
Voice Control
Child Lock
PreciSense LiDAR
$379.99 $549.99
Auto-Empty Dock Pure
4200Pa Suction
3D Mapping
5200mAh Battery
Voice Control
Child Lock
$459.99 $799.99
q7max

Q7 Max+

Simple Cleaning. Simpler Emptying.

Play Video

q7max

42001 Pa
Suction Power

q7max

Auto-Empty Dock Pure Support

q7max

300g Consistent Mop Pressure

q7max

PreciSense Precision LiDAR

q7max

3D Mapping

q7max

Custom Cleaning Routines

Roborock Q7 Max+ combines a wide range of effective robot vacuum technologies proven in generation after generation of Roborock vacuum. It delivers uncompromising vacuuming effectiveness, incredible ease of use, and the absolute convenience of the Auto-Empty Dock Pure.

Serious Suction Power

Drag away dirt hiding in your carpets and lift off debris hiding in floorboard cracks with a maximum suction power of 42001 Pa.

Durable Grime Removal

A long-lasting all-rubber brush powerfully agitates carpets to release more dirt, flicks dust into the vacuum stream, and strongly resists hair tangles. Able to move across multiple panes, it keeps close to the ground for more effective cleaning.

7 Weeks2

Without Emptying

2.5L

Dustbag

7 Weeks

Without Emptying

Clean often, empty rarely with the Auto-Empty Dock Pure. It empties your robot automatically into its 2.5 L dustbag, every clean, for up to 7 weeks2. When the bag is full, it can be swapped out in seconds.

2.5L

Dustbag

7 Weeks

Without Emptying

Twin Cleaning Power

Vacuum and mop simultaneously to capture fine dirt that vacuuming alone might miss. Equipped with an electronic pump, the Q7 Max+ offers 30 water flow levels so you can fine-tune cleaning to match your floor types and preferences.

240 sqm

Maximum Mopping Range3

300 g

Consistent Mop Pressure

Electronic Mopping

30 Water Flow Levels

Twin Cleaning Power

Vacuum and mop simultaneously to capture fine dirt that vacuuming alone might miss. Equipped with an electronic pump, the Q7 Max+ offers 30 water flow levels so you can fine-tune cleaning to match your floor types and preferences.

240sqm

Maximum Mopping Range3

300g

Consistent Mop Pressure

Electronic Mopping

30 Water Flow Levels

Combined Dustbin
& Water Tank

Combining the dustbin and the water tank into one unit increases the capacity of both. It also makes it easier to empty the bin and refill the tank in one trip.

470 ml

Dustbin Capacity

350 ml

Water Tank Capacity

Clean On
and On

Driven by a large 5200mAh Li-ion powerhouse, Q7 Max+ can clean non-stop for up to 3 hours4 on a single charge. Easily enough range to tackle most homes.

300 sqm

Maximum Vacuuming Area

Combined Dustbin
& Water Tank

Combining the dustbin and the water tank into one unit increases the capacity of both. It also makes it easier to empty the bin and refill the tank in one trip.

470 ml

Dustbin Capacity

350 ml

Water Tank Capacity

Clean On
and On

Driven by a large 5200mAh Li-ion powerhouse, Q7 Max+ can clean non-stop for up to 3 hours4 on a single charge. Easily enough range to tackle most homes.

300 sqm

Maximum Vacuuming Area

PreciSense Precision LiDAR

Roborock's PreciSense LiDAR system is the brains behind your robot's extraordinary ability to find the most efficient way to clean throughout your home. The maps it creates power a suite of features controlled in the Roborock app.

Scheduling
Life in a home can be complicated. You can create custom cleaning schedules that work for your home with advanced scheduling. Pick your time of day, suction power, and the room(s) you need, and it will repeat automatically.
Multi-Level Mapping
Many homes have multiple levels. Multi-level mapping systems automatically recognize different levels of your home. All you have to do is put the robot down. No additional docks, no need to identify the level in your app. Up to four levels are supported.
No-Go Zones and
Invisible Walls
No-Go Zones define an area that the robot cannot go, while Invisible Walls draw a line and are good for sealing off rooms and corners. Every level in your home can have No-Go Zones and Invisible Walls. All are placed automatically after the level has been recognized.
3D Mapping
Take a new look at your home and get a clearer understanding of your layout with 3D Mapping. You can even add furniture and floor materials to create a more accurate representation of your home.
Routines
Do you cook a lot? Find yourself always turning up the suction and sending the robot to the kitchen? Set a routine for that and do it with one tap instead of several. You can also add schedules to any routine you set.

Speak to Command

Take control of your robot, start cleanups, send it to tackle specific rooms, and more with just the power of your voice. Amazon Alexa, Google Home, and Apple Siri Shortcuts are supported.

Keep Kids
& Pets Safe

Curious kids and clumsy pets might accidentally start a clean with the push of a button. Stop that from happening with the Child Lock.

Worry-Free Roaming

Have confidence that your Q7 Max can wander safely around your home. The Sensient sensor array includes a suite of sensors, including cliff sensors, accelerometers, bumpers, and more. It will avoid rolling off of steps, getting trapped, or slamming into your walls.

FAQ
  • Q.
    What is the difference between Q7 Max and Q7 Max+?
    A.
    Q7 Max is the robot vacuum cleaner only, Q7 Max+ contains a robot vacuum cleaner and an auto-empty dock, which names Auto-Empty Dock Pure.
  • Q.
    Will the Auto-Empty Dock Pure be sold separately?
    A.
    Temporarily Roborock has no plans to sell it separately.
  • Q.
    Is the Auto-Empty Dock of Roborock S7 compatible with the Q7 Max?
    A.
    It's incompatible.
  • Q.
    What are the dimensions of Roborock Auto-Empty Dock? How much free space should I allow around it?
    A.
    The dimensions of Roborock Auto-Empty Dock are 442*306*425 mm (18 × 12.4 × 15.1 in). Please keep at least 0.5 m (1.6 ft) of clearance on either side, 1.5 m (5 ft) in front, and 1 m (3 ft) above.
  • Q.
    What is the capacity of Roborock Auto-Empty Dock (Cyclone)?
    A.
    The dustbin has a capacity of 2.5 L. It can generally be used for 45 days without emptying. To ensure optimal performance, clean the dustbin regularly or when the dust reaches the MAX mark.
  • Q.
    What are the differences between the Q7 Max and the S5 Max?
    A.
    1. The suction power of the fan is increased from 2000Pa to 4200Pa, the suction power is stronger, and the cleaning is more thorough;
    2. However, it is suitable for the dust bag version of the automatic dust collecting and charging seat (OnyxC);
    3. Add child lock mode: prevent children and pets from accidentally touching the buttons;
    4. Constant humidity electric control water tank, 30-level regulation, soft glue water outlet (more precise control, more uniform water output);
    5. Integrated design of dust box and water tank: adding water and dumping dust in one step, maintenance is more convenient;
    6. The capacity of the water tank is increased from 290ml to 350ml: the wet mopping area is larger;
    7. Added 3D map mode.
  • Q.
    Is it normal if the machine body and top cover are scratched after use?
    A.
    As your machine will inevitably be slightly scratched and impacted during use, it is subject to normal trace of use that will not present an impact on product performance.
  • Q.
    What's the height of the machine?
    A.
    The machine has the overall height of about 9.65cm and may not be applicable to areas where furniture is 11cm high or below.
  • Q.
    What's the diameter of the machine?
    A.
    The machine has the diameter of 353*350*96.5mm and may not be applicable to areas with width lower than 38 cm.
  • Q.
    What's the small brush in the right of the machine?
    A.
    This is the side brush of the robotic vacuum cleaner. The side brush, when running, is mainly used to sweep waste along the wall or barrier up to the bottom of the main brush, which is then suctioned into the dust bin.
  • Q.
    Is it normal that the loose portion in the front of the machine is movable?
    A.
    The structural member in the front side that can be compressed is a bumper. This is an important sensor structure that helps the machine to detect a barrier in the range of 180 degrees in the front. A barrier in the front can be effectively detected with a slight physical impact.
  • Q.
    Why does a circular orange rotating portion protrude from the top? Is it normal that the top cover can be pushed? Is it normal that the top cover is loose?
    A.
    The protrusion portion set on the top is the core component of the machine, i.e. LDS (laser distance sensor). It rotates constantly at 300 RPM to obtain topographic data around the machine itself. Outside the laser distance sensor is its protective cover. On the bottom of the LDS top cover is the LDS cover bumper sensor which is capable of detecting any foreign matter that may get stuck in the laser head and of automatically returning back to prevent machine jamming.
  • Q.
    What is the capacity of the water tank? What is the difference between the previous bionic water tank?
    A.
    Q7 MAX uses an electronically controlled water tank with a capacity of 350ml. The drawer type mop bracket is installed along the original drawer design of the stone sweeping machine. The sweeping and towing switch does not need to flip the fuselage or disassemble the water tank, which is convenient and quick. The mop support constant pressure mopping design, the mopping pressure is not affected by the amount of remaining water, ensuring the mopping effect. It has a larger capacity than the bionic water tank and a stronger downforce.
  • Q.
    Is the upper cover of the machine rugged, or is it easily broken?
    A.
    Both the upper cover and its joint point are made of resilient materials. The upper cover will not be easily broken except for malicious damage.
  • Q.
    Is the upper cover wear resisting?
    A.
    The In-Mold Decoration by Roller (IMR) technology is used for the upper cover such that the surface is very smooth and flat and will not be scratched except for malicious damages such as use of a hard object or pointed object.
  • Q.
    What should I do when the laser head protective cover of the machine is easy to be stained?
    A.
    As this is the highest point of the machine, it is hard to avoid being scratched by the bottoms of some furniture, but this will not present an impact on the machine performance. If you still care, you can make some circular films by yourself to protect it.
  • Q.
    Why is only one side brush provided rather than two?
    A.
    Firstly, the side brush of the robotic vacuum cleaner is mainly used to clean waste accumulated along a wall or at the root of an obstacle. The side brush is not a main cleaning structure when cleaning in other areas. For example, for non-wall cleaning, if the side brush always runs in high speed, it may make the waste fly about. The side brush can be dynamically regulated and the speed of the side brush will be reduced for non-wall cleaning to prevent waste flying about. Secondly, it is designed in such a way that only one side cleans against a wall or the root of an obstacle and the side brush is not required in the other side. Finally, if two side brushes are designed, when cables are twined, two side brushes running in reverse direction are more easily to be twined such that the machine can be easily twined. From the above, only one side brush is designed.
  • Q.
    What's the best location to set the charging dock?
    A.
    The charging dock should be set in such a way that about 0.5 m in left and right each, 1.5 m or more in the front are reserved, with its backside against the wall. It is generally recommended to set the charging dock in your living room that is generally spacious. Do not set the charging dock in a confined and congested place.
  • Q.
    Is a bumper strip required?
    A.
    The machine is provided with a laser distance sensor, allowing the machine to automatically reduce its speed in most instances. In addition, the bottom of the machine is provided with a bumper strip. As impact is very slight at home, an additional bumper strip is not required. At the same time, if the ultrasonic sensor or wall sensor is blocked by your purchased bumper strip, the machine may not work normally.
  • Q.
    Is it suitable for solid wood/composite/archaized/tile floor?
    A.
    Well, the machine works well on all these floors and will surely not scratch them.
  • Q.
    Can it clean effectively?
    A.
    The floating main brush structure of the machine is capable of fitting closely onto the floor to take waste into the dust bin; the high power fan provides high negative pressure to collect dust; the self-regulating side brush is capable of cleaning waste along the wall and in front of furniture; the path programming navigation algorithm allows the machine to cover all areas to clean; the combination of the features above ensures its good cleaning effectiveness.
  • Q.
    How long will it take to clean my home?
    A.
    It depends on operating time, room size, furniture arrangement, etc. In generally, it takes not more than 60 minutes to clean a 100 sq. m. room, and may be shorter if furniture is well arranged and there is little waste.
  • Q.
    Is it suitable for overseas markets?
    A.
    The power supply works well in the range of 100-240V/50-60HZ and thus can be used in overseas markets.
  • Q.
    Is timer cleaning supported? How to set it?
    A.
    Yes. Please download Roborock app and connect it to your machine. On the Setting option, you can add timer operation. After setting, the set timer cleaning will not be affected regardless of whether the machine is connected to Wi-Fi.
  • Q.
    Is it suitable for a carpet?
    A.
    It works well on undercoat or suede carpets, but may not be suitable for some shag carpets or dark carpets because shag carpets may block the cliff sensor on the bottom of the machine, thereby making the machine regard it as a cliff that it should avoid. This is also true for some dark carpets that may have good light absorption ability.
  • Q.
    Can I move the machine when it is working?
    A.
    You can pause the machine midway and make it move in a small range. However, for a long movement distance, the machine may restart cleaning due to path programming failure.
  • Q.
    Can it work normally in a completely black environment?
    A.
    Of course. All sensors attached on the machine body can work well in a completely black environment.
  • Q.
    Is 5GHz Wi-Fi or 802.1x verification mode supported?
    A.
    Only 2.4GHz Wi-Fi is supported; ways of encryption requiring input of user name like 5G and 802.1x are not supported.
  • Q.
    Can it automatically empty the waste?
    A.
    Q7 MAX supports smart dust collection charging stand, you can choose to buy it.
  • Q.
    Will your private information be public?
    A.
    No. All data is stored in your machine. User map or other data will surely not be uploaded to the server. If you check the Customer Experience Improvement Program, part of error logs will be uploaded to the server to help us further improve our products.
  • Q.
    Is there a potential risk of electric shock when touching the charging dock?
    A.
    No. Firstly, the charging dock outputs no current except when the machine is connected; secondly, the charging dock without the machine has the output voltage of DC 4.2 V which is far less than 36 V, the safe voltage for human body; finally, please be assured that the charging dock is provided with short circuit and current leakage protection features such that it can be automatically powered off in abnormal situations.
  • Q.
    What is the sound level of the robotic vacuum cleaner?
    A.
    When measuring at 1 m away, the sound level is between about 53 and 61 dB. It may have a slight difference depending on machine model.
  • Q.
    How long will the robotic vacuum cleaner take to charge?
    A.
    About 240 minutes for 20->80%
  • Q.
    What's the detection range and precision of the laser head?
    A.
    The laser distance sensor has the precise ranging scope within 6 m and has the precision accurate to ±1% of error within 3 m, that is, less than 1 cm in 1 m.
  • Q.
    Is the laser sensor harmful to children or pets?
    A.
    It is designed in accordance with IEC 60825-1:2014 laser safety level Class 1 and will not generate hazardous radiation. Please be assured that this is tested in TÜV Rheinland in Germany and described in the Manual.
  • Q.
    What kind of fan is used and what is the suction capacity?
    A.
    A world-class brushless fan manufactured by NIDEC is used, with the suction capacity up to 4200 Pa.
  • Q.
    Is dust full detection provided?
    A.
    No. If the dust bin is left uncleaned for a prolonged period of time, the machine will give a voice prompt to ask you to clean the dust bin and your mobile phone will also send you a message to ask you to clean the dust bin. Dust full sensors used in other commercially available products are easily blocked by dust and thus frequently make misjudgment that the dust bin is full.
  • Q.
    Will long-term charging consume more power? Will overcharge shorten the service life of the battery?
    A.
    Charging stops after the battery is full. The motherboard is powered directly from the charging dock and the battery is in standby mode and thus the battery performance will not be affected. The machine has very low power consumption (less than 3 W) when it is inoperative. To maintain the best performance of the battery, please try to keep the machine interfaced on the charging dock when it is left unused.
  • Q.
    How long can it work in full charge state?
    A.
    It depends on operating time, floor material and mode of operation. For a common floor without a carpet, the machine in full charge state can work for about 2.5 hours in standard mode, shorter time in Strong mode and longer time in Silent mode.
  • Q.
    Is electric motor overload protection mechanism available?
    A.
    All electric motors are provided with a motor overload protection mechanism, including side brush motor, main brush motor, main wheel motor, LDS motor and vacuum cleaner fan motor.
  • Q.
    What's the RPM of the side brush, main brush and fan?
    A.
    The side brush can be dynamically regulated and works at 330 RPM along a wall and 130 RPM in other conditions. The main brush works at 1350 RPM while the vacuum cleaner fan in standard mode works at 12000 RPM.
  • Q.
    What kind of lithium battery is used and what's the capacity?
    A.
    Lithium battery with capacity of 5200 mAh and voltage rating of 14.4 V.
  • Q.
    Do I have to power the machine off after cleaning?
    A.
    No. The machine will automatically return to the charging dock after cleaning for recharging, and in full charge state, the machine is directly powered by the charging dock and will not consume the battery power. This is beneficial to extend the service life of the battery.
  • Q.
    Can the machine still work after the main brush is removed?
    A.
    The machine itself will not fail to work due to an error and can still works without the main brush, but, without the main brush, the cleaning effect is reduced. This is not recommended.
  • Q.
    Advantages of electronically controlled water tanks?
    A.
    The electronically controlled water tank adopts a precision micro-controlled peristaltic pump, which has a longer service life, anti-clogging, more precise water output control, and three-speed adjustable water volume.
    More intelligent: do not spray water when not moving, do not spray water when slipping, get out of trouble and other abnormal situations, to prevent the floor from soaking. Only spray water when cleaning, not when recharging.
  • Q.
    How many Virtual walls, No-go zones and No-map zones can we set up?
    A.
    When the machine is online, you could add up to 10 No-go zones, 10 No-map zones and 10 Virtual walls separately. The No-go zones and the Virtual walls can be overlapped.
  • Q.
    Is it necessary to buy a virtual wall even if the machine could set up Virtual wall and No-go zone function?
    A.
    Q7 MAX does not support physical virtual walls. If you need to set virtual walls or restricted areas, please open the map save and set software virtual walls or restricted areas in the map.
  • Q.
    Can the side brush, main brush and dust bin be flushed with water?
    A.
    Yes. After flushing, please thoroughly dry and reinstall them in place, especially for the filter; otherwise, you may have to clean up it.
  • Q.
    Can the filter be flushed with water? Why?
    A.
    Yes. The Roborock robotic vacuum cleaner is provided with a washable filter. When the dust collection effect is affected due to seriously dirty filter, flush the filter with tap water but not to use a cleaner or brush. Dry it thoroughly before use.
Thanks for subscribing!
OK